Ask Your Question
0

Ethernet Adapter Problems

asked 2014-08-06 22:18:02 -0500

cgonz31 gravatar image

updated 2014-08-11 22:18:32 -0500

I am running Fedora 20 (64-bit) with kernel 3.15.7-200.fc20.x86_64. The ethernet adapter is a Qualcomm Atheros AR8162. The output of ifconfig is:

em1: flags=4099<UP,BROADCAST,MULTICAST>  mtu 1500
        inet6 fe80::28c:faff:fe65:57c5  prefixlen 64  scopeid 0x20<link>
        ether 00:8c:fa:65:57:c5  txqueuelen 1000  (Ethernet)
        RX packets 506008  bytes 387032847 (369.1 MiB)
        RX errors 3  dropped 1  overruns 3  frame 0
        TX packets 103458  bytes 15283165 (14.5 MiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
        device interrupt 16  

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        inet6 ::1  prefixlen 128  scopeid 0x10<host>
        loop  txqueuelen 0  (Local Loopback)
        RX packets 6827  bytes 541916 (529.2 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 6827  bytes 541916 (529.2 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

wlp2s0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet 192.168.1.8  netmask 255.255.255.0  broadcast 192.168.1.255
        inet6 fe80::26fd:52ff:fe7c:dc7a  prefixlen 64  scopeid 0x20<link>
        ether 24:fd:52:7c:dc:7a  txqueuelen 1000  (Ethernet)
        RX packets 1854223  bytes 2764917834 (2.5 GiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 1056396  bytes 95087957 (90.6 MiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

I can connect to the wired network at school but I cannot connect at home. I know it is not my ethernet cable or my router as I can connect with a Windows 7 computer at home. Since I can connect at school, my ethernet adapter works but I don't have any idea why I can't connect at home. Any ideas what it could be?

I do not know what setup my university runs for the wired network except that I had to register my laptop on their website. At home, I have a Motorola SURFboard SB5101N cable modem and a Netgear N300 WNR2000v4 wireless router. My laptop is a Toshiba Satellite C50-A.

EDIT:

I do not have any proxy setup. Connected to the school network the output of ifup em1 is:

/usr/sbin/ifup: configuration for em1 not found.
Usage: ifup <configuration>

Apparently ethtool is the right one. The output of ethtool em1 is:

Settings for em1:
    Supported ports: [ TP ]
    Supported link modes:   10baseT/Half 10baseT/Full 
                            100baseT/Half 100baseT/Full 
    Supported pause frame use: Symmetric Receive-only
    Supports auto-negotiation: Yes
    Advertised link modes:  10baseT/Half 10baseT/Full 
                            100baseT/Half 100baseT/Full 
                            1000baseT/Full 
    Advertised pause frame use: Symmetric
    Advertised auto-negotiation: Yes
    Speed: 100Mb/s
    Duplex: Full
    Port: Twisted Pair
    PHYAD: 0
    Transceiver: internal
    Auto-negotiation: on
    MDI-X: Unknown
Cannot get wake-on-lan settings: Operation not permitted
    Current message level: 0x000060e4 (24804)
                   link ifup rx_err tx_err hw wol
    Link detected: yes

I'll post the outputs while connected at home tonight.

EDIT:

While connected at home with the ethernet ... (more)

edit retag flag offensive close merge delete

Comments

ifup em1 and post results. Try switching to static ip. Also, ethtool em1 (I think that's the right one, correct me if I'm wrong).

abadrinath gravatar imageabadrinath ( 2014-08-07 02:38:48 -0500 )edit

Do you have some proxy set up?

lnxslck gravatar imagelnxslck ( 2014-08-07 03:42:44 -0500 )edit

can you ping the gateway "Netgear N300 WNR2000v4 wireless router" ?

natecult gravatar imagenatecult ( 2014-08-10 20:16:15 -0500 )edit

Switch to static ip help?

abadrinath gravatar imageabadrinath ( 2014-08-11 01:52:54 -0500 )edit

1 Answer

Sort by ยป oldest newest most voted
0

answered 2014-08-18 08:56:52 -0500

cgonz31 gravatar image

Update to 3.14.8-200.fc20.x86_64 kernel. Problem disappeared on its own after update.

edit flag offensive delete link more

Your Answer

Please start posting anonymously - your entry will be published after you log in or create a new account.

Add Answer

Question Tools

1 follower

Stats

Asked: 2014-08-06 22:18:02 -0500

Seen: 690 times

Last updated: Aug 18 '14